Home » Categories » Riflescope Mounting

Difference between Picatinny and Weaver Rail

When you are looking for rail accessories, there are many different parts and accessories that use the words Picatinny and Weaver to describe what they are compatible with.

Just what is a Picatinny Rail anyway? And how is it different from a Weaver?

The "Picatinny Rail” is a term that has evolved in the firearm industry from a military standard, specifically MIL-STD-1913 (AR) which was adopted on February 3, 1995. The title of the publication is "Dimensioning Of Accessory Mounting Rail For Small Arms Weapons” and this document specified exactly what the dimensions and tolerances were for any mounting systems that were to be submitted for acceptance by the military. The term "Picatinny” comes from the place of origin for this system, the Picatinny Arsenal located in New Jersey. MIL-STD-1913 specifies the dimensions required for consideration, including length, width, height, and angles and the tolerances allowed for each measurement. The key distinction of the MIL-STD-1913 lies in the specification for the profile and the recoil groove.

What are the differences between the "Picatinny” and the "Weaver” systems?

The profile of the two systems is virtually identical. Depending on the quality of the machining done by the manufacturer, the two systems should be indistinguishable from the profile. The key difference lies in the placement of the recoil grooves and with width of the grooves. MIL-STD-1913 (Picatinny) grooves are .206”  (5.23mm) wide and have a center-to-center width of .394” (10mm). The placement of these grooves has to be consistent in order for it to be a true "Picatinny” MIL-STD system. Weaver systems have a .180” (4.57mm) width of recoil groove and are not necessarily consistent in a center-to-center measurement from one groove to the next. In many instances, a Weaver system has a specific application that it is machined for, so interchangeability is not necessarily an issue. A MIL-STD-1913 system must adhere to the specifications listed above in order for it to be considered MIL-STD, since the military desires uniformity in the recoil grooves to allow for different systems to be mounted on the weapon with no concern for compatibility.

Now, what does this mean to you?

Boiled down, it means that accessories designed for a Weaver system will, in most cases, fit on a "Picatinny” system. The reverse, however, is probably not the case. Due to the larger recoil groove, "Picatinny” accessories will not fit a Weaver system. There are, of course, exceptions to every rule, but for a good rule-of-thumb, "Picatinny” won’t fit Weaver, but Weaver will fit "Picatinny”.

4.8 (5)
Article Rating (5 Votes)
Rate this article
  • Icon PDFExport to PDF
  • Icon MS-WordExport to MS Word
Attachments Attachments
There are no attachments for this article.
Comments Comments
There are no comments for this article. Be the first to post a comment.
Related Articles RSS Feed
Rear Extended Picatinny Rails for Night Vision
Viewed 2156 times since Thu, Nov 2, 2017
Picatinny or Weaver Rail and Bases Mounting Procedure
Viewed 10631 times since Thu, Jun 23, 2016
Scope Mounting - What Mounts Height Do I Need?
Viewed 7474 times since Wed, Jul 13, 2016
Scope Mounts for Blaser (R93, R8 and others)
Viewed 13504 times since Fri, Sep 12, 2014
Scope Mounting on the Sako Tapered Dovetail
Viewed 15322 times since Thu, Jul 14, 2016
Scope Mounting Instructions - Getting the Correct Height for Picatinny Rail & Rings
Viewed 22222 times since Wed, Mar 5, 2014
Sauer 101 Picatinny Rail Scope Mount Information
Viewed 22770 times since Thu, Jun 19, 2014
Mounting Multiple Scopes on to One Rifle without Losing Zero
Viewed 6559 times since Thu, Jul 10, 2014
Anschutz Rifle Measurements for Mounting Scopes
Viewed 41368 times since Wed, Jul 9, 2014